Post by BozoWise on Nov 9, 2003 12:31:57 GMT -5
After a trip to the range and cleaning all the dust off one of my pre 64's I was more then disappointed in the trigger. I hadn't shot this rifle in over 8 years so it time to see some work killing yotes and goats. Here is the information I found incase anyone needs it.
Adjusting the Model 70 Trigger
Let me discuss how the trigger on the Model 70 works. Knowing how it works will allow you to know how a gunsmith would adjust it.
The trigger mechanism on the Winchester Model 70 is remarkably simple. Remove the barreled acton of a Model 70 from it's stock and you can see just how simple it is. You will see a trigger that pivots on a pin. Look at the rear portion of the trigger (normally hidden by the stock) and you will see a square head screw (the trigger stop screw), three nuts, and a spring (we'll call it
the trigger return spring).
The purpose of the trigger stop screw is to limit the amount of over travel of the trigger. It is possible to screw the trigger stop screw in far enough that you will not be able to pull the trigger enough to release the sear. Ideally the trigger stop screw should be screwed in as far as it can and still have enough trigger movement to reliably release the sear. This will allow for the greatest amount of adjustment of the trigger spring tension.
Tension on the trigger return spring determines a majority of the trigger pull weight (the rest of the trigger pull weight comes from the friction between the trigger and the sear). The spring surrounds the trigger stop screw, both can be seen just behind the trigger. The trigger stop screw is held in place by a pair of captive nuts, one on each side of the part of the trigger the stop screw passes through. A third nut sets the tension on the trigger spring. Tightening this third nut (turning it clockwise) against the trigger spring will increase the trigger pull. And turning it counter clockwise will decrease the trigger pull weight.
After making any adjustments, be absolutely sure to test for an excessively light trigger. To do this, screw the barreled action back in the stock. With the bolt cocked, in the closed position on an empty chamber, and the safety off, butt down the rifle. That is hold the rifle barrel pointing upward, let the butt bounce on the ground. It should take a considerable bump to cause the firing pin to drop (on the empty chamber).
On a friend's pre-64 Model 70 trigger, the spring had to be changed because enough of the trigger spring pretension could not be removed to get an acceptable trigger pull weight. Yet on another (on one of those new classic actions), it was possible to remove ALL of the trigger spring pretension. This is a dangerous situation because only the trigger to sear tension keeps the cocked rifle from firing.
Well I hope you now have a better understanding of how a Model 70 trigger works. Of course for all trigger pull weight adjustments you should take your rifle to a reputable gunsmith.
Adjusting the Model 70 Trigger
Let me discuss how the trigger on the Model 70 works. Knowing how it works will allow you to know how a gunsmith would adjust it.
The trigger mechanism on the Winchester Model 70 is remarkably simple. Remove the barreled acton of a Model 70 from it's stock and you can see just how simple it is. You will see a trigger that pivots on a pin. Look at the rear portion of the trigger (normally hidden by the stock) and you will see a square head screw (the trigger stop screw), three nuts, and a spring (we'll call it
the trigger return spring).
The purpose of the trigger stop screw is to limit the amount of over travel of the trigger. It is possible to screw the trigger stop screw in far enough that you will not be able to pull the trigger enough to release the sear. Ideally the trigger stop screw should be screwed in as far as it can and still have enough trigger movement to reliably release the sear. This will allow for the greatest amount of adjustment of the trigger spring tension.
Tension on the trigger return spring determines a majority of the trigger pull weight (the rest of the trigger pull weight comes from the friction between the trigger and the sear). The spring surrounds the trigger stop screw, both can be seen just behind the trigger. The trigger stop screw is held in place by a pair of captive nuts, one on each side of the part of the trigger the stop screw passes through. A third nut sets the tension on the trigger spring. Tightening this third nut (turning it clockwise) against the trigger spring will increase the trigger pull. And turning it counter clockwise will decrease the trigger pull weight.
After making any adjustments, be absolutely sure to test for an excessively light trigger. To do this, screw the barreled action back in the stock. With the bolt cocked, in the closed position on an empty chamber, and the safety off, butt down the rifle. That is hold the rifle barrel pointing upward, let the butt bounce on the ground. It should take a considerable bump to cause the firing pin to drop (on the empty chamber).
On a friend's pre-64 Model 70 trigger, the spring had to be changed because enough of the trigger spring pretension could not be removed to get an acceptable trigger pull weight. Yet on another (on one of those new classic actions), it was possible to remove ALL of the trigger spring pretension. This is a dangerous situation because only the trigger to sear tension keeps the cocked rifle from firing.
Well I hope you now have a better understanding of how a Model 70 trigger works. Of course for all trigger pull weight adjustments you should take your rifle to a reputable gunsmith.
